TribeCreek Subscribe on YouTube

Home › Ford & Fordson › Thousand Series and the 1960s–70s (1961–1975)

Decoding Ford Thousand Series Model Numbers (2000, 4000, 6000, 1962–1964): Digit by Digit

Updated November 21, 2026 · Sources are linked in the text

A blue-and-gray Ford with a 2000 or 4000 emblem could have been built in 1962 or in 1975, and the two are almost completely different tractors. The early ones are four-cylinder tractors closely related to the 601 and 801. From 1965 the same names went on a new three-cylinder range. Parts, values and even where to find the serial number depend on which one you have.

On a 1962–1964 tractor, the stamped model number tells you a lot more than the emblem: engine size, chassis type, transmission and PTO. People quote it as a four-digit number such as 2110 or 4140, but the stamping usually has five digits, plus sometimes a suffix. This page walks through each part, decodes example stampings step by step, and explains how to tell an early tractor from a 1965-on one.

Video: Ford Thousand Series Tractors Explained (2000/4000/6000, 1962–1964) (4:41) · Watch on YouTube

What the 1962–1964 Thousand Series was

According to the N Tractor Club, Ford introduced the 2000, 4000 and 6000 in 1962. The 2000 and 4000 were essentially the 601 and 801 with a restyled grille that ended ten years of the "cyclops" front emblem, painted Ford blue with lighter gray trim. The 6000 was an all-new, much larger six-cylinder Select-O-Speed tractor (N Tractor Club Quick ID guide). Tractor Data describes the four-cylinder 2000 as very similar to the 601 Workmaster and entirely different from the three-cylinder 2000 that replaced it (Tractor Data).

The numbering actually started earlier. Near the end of 1960 Ford introduced the first Thousand Series tractors as industrial models, painted red and "buff": the light industrial 2030 and 4030 and the heavy industrial 4040, basically modified 01-series tractors (N Tractor Club).

The decoding chart below covers the 2000 and 4000, which each have their own model page: the Ford 2000 and the Ford 4000. The 6000 is a different tractor and has its own page.

Where the numbers are stamped

On 1962–1964 tractors the model and serial numbers are in the same place as on the Hundred and 01 series: the left side, on the flat area above and behind the starter (N Tractor Club). My Ford Tractors describes it as the left front top corner of the transmission housing (My Ford Tractors). The model number is on top and the serial below it, between diamond symbols. Clean the pad with a wire brush and solvent and read it with a light held low to one side.

The five digits

These tables follow the N Tractor Club chart. My Ford Tractors' decode table gives the same codes.

First digit: engine

2____134 cu in gasoline or 144 cu in diesel (2000)
4____172 cu in gasoline, LP-gas or diesel (4000)

Second digit: production period

_0___Industrial models produced before 1963
_1___Industrial and agricultural models produced later (the chart says after 1963)

Third and fourth digits: chassis

__10_Row-crop
__11_Offset
__20_Utility with adjustable front axle
__21_Orchard with non-adjustable front axle
__30_Utility with non-adjustable front axle (light industrial)
__31_Low center of gravity (LCG)
__40_Heavy-duty industrial with subframe
__41_Heavy-duty industrial with subframe and cast grille

So a "2110" is a 2000 row-crop and a "4140" is a 4000 heavy-duty industrial, both from the later period.

Fifth digit: transmission, PTO and hydraulics. Its meaning depends on the second digit:

Second digit 01: 4-speed, no PTO or hydraulics. 2: 4-speed with hydraulics, no PTO. 3: 4-speed with hydraulics and PTO. 4: Select-O-Speed, no hydraulics or PTO. 5: Select-O-Speed with hydraulics and 540 PTO. 6: Select-O-Speed with hydraulics, 540/1000 and ground-speed PTO. 9: 5-speed with live PTO
Second digit 10: 4-speed, no PTO. 1: 4-speed with PTO. 2: 5-speed with live PTO. 4: Select-O-Speed, no PTO. 6: Select-O-Speed with 540/1000 independent PTO. 7: Select-O-Speed with 540/1000 independent and ground-speed PTO

Suffixes: -1 tricycle with single front wheel, -4 high clearance with wide front, -L LP-gas, -D diesel.

One caution on the fifth digit: the references don't fully agree. Tractor Data's listing for the 2130-series industrial gives 21301 as a four-speed with no three-point or PTO and lists 21303 and 21305, codes the N Tractor Club chart doesn't have for a second digit of 1 (Tractor Data). Treat the fifth digit as a pointer and confirm the transmission, PTO and lift by looking at the tractor.

Serial numbers

19621,001
196311,948 (N Tractor Club; My Ford Tractors decode table; Tractor Data industrial listings) / 11,949 (My Ford Tractors serial page; Tractor Data 2000 and 4000 pages)
196438,931

Sources: the N Tractor Club guide, My Ford Tractors, and Tractor Data's 2000 and 4000 pages. The one-number difference at 1963 only matters for serial 11,948.

The earlier industrials are different. Tractor Data dates its 4030-series listing with the 01-series numbers (1960 from 105,943, 1961 from 131,427, 1962 from 155,531), while its later 4130-series listing uses the 1962–1964 table above (4030; 4130).

Worked examples

Example 1 (made-up numbers): 41206 over ◇24617◇.

  1. 4: 172 cu in, a 4000.
  2. 1: the later code set.
  3. 20: utility with adjustable front axle.
  4. 6 (with a second digit of 1): Select-O-Speed with 540/1000 independent PTO.
  5. 24617 falls between 11,949 and 38,930: 1963.

Result: a 1963 Ford 4000 utility with Select-O-Speed. Check that the tractor really has the powershift lever and a two-speed PTO.

Example 2 (made-up numbers): 21102-1 over ◇41870◇.

  1. 2: 134 cu in gas or 144 cu in diesel, a 2000. There's no -D suffix, so it isn't marked as a diesel.
  2. 1: later code set.
  3. 10: row-crop.
  4. 2: five-speed with live PTO.
  5. -1: tricycle with a single front wheel.
  6. 41870 is above 38,931: 1964.

Result: a 1964 Ford 2000 row-crop with a five-speed, live PTO and single front wheel.

Example 3 (made-up numbers): 40303 over ◇140210◇.

  1. 4: 172 cu in.
  2. 0: industrial built before 1963.
  3. 30: light industrial, non-adjustable front axle.
  4. 3 (with a second digit of 0): four-speed with hydraulics and PTO. Tractor Data's 4030 listing agrees: 40303 is "PTO and hydraulics."
  5. 140210 is far above anything on the 1962–1964 table, so use the 01-series numbers: 131,427 to 155,530 is 1961.

Result: a 1961 Ford 4030 light industrial. A second digit of 0 is the signal to check the 01-series serial chart.

How the 1965 Thousand Series differs

From 1965 the 2000 and 4000 names went on new three-cylinder tractors. Tractor Data calls the three-cylinder 4000 "entirely different" from the old 801-based one (Tractor Data). The quickest checks:

  • Cylinders. Count the spark plugs or injectors: four on a 1962–1964 tractor, three on a 1965-on 2000 or 4000.
  • Stamping side. 1965–1975 numbers are on the right side of the transmission housing, not the left (My Ford Tractors).
  • Format. 1965-on tractors carry three lines: a model code, a production date code, and a serial with a letter prefix (US-built tractors start at C100000 in 1965). The Ford 5000 page shows how to decode that format.

Mistakes to avoid

  • Reading the fifth digit without the second. A 2 means "four-speed with hydraulics, no PTO" after a 0 and "five-speed with live PTO" after a 1.
  • Dating by the second digit. It tells you which code set applies, not the year. Date the tractor from the serial.
  • Using the 1962–1964 serial table on a 0-series industrial. Those use the much higher 01-series numbers, and a forced match gives the wrong year.
  • Ordering parts for "a Ford 2000" or "a 4000." Tractor Data calls the four-cylinder and three-cylinder versions entirely different tractors. Tell the parts supplier which one you have, with the stamping.
  • Trusting paint. The N Tractor Club notes a red 6000 built in 1962 and red-and-buff industrials. Blue isn't a date, and red doesn't make a Ford an 01 series.

All Ford & Fordson tractor guides →