Ford 4000 (1962–1975): Telling the Three Generations Apart and What to Check
"Ford 4000" covers three different tractors. From 1962 to 1964 it was a four-cylinder built on the 801 Powermaster. From 1965 it was an all-new three-cylinder, and in April 1968 that tractor got new sheet metal, a bigger gas engine and a new model code. An ad that just says "Ford 4000" doesn't tell you which one it is, and engines and drivetrains don't interchange between the four-cylinder and the three-cylinder.
This page covers telling the three apart, reading the stamped numbers on each, and what to check before buying.
A short history
Ford's four-cylinder Thousand Series tractors, the 2000 and 4000, came out in 1962, joining the six-cylinder 6000. The N Tractor Club describes the 2000 and 4000 as "basically the same as the 601 and 801 series tractors," with a restyled grille and Ford's new blue paint with lighter gray trim (N Tractor Club Quick ID guide). Tractor Data notes that the three-cylinder 4000 of 1965 was "entirely different from the old 801-based 4000 tractor" (Tractor Data).
That new tractor was part of Ford's worldwide range, launched at the Royal Smithfield Show in December 1964 as the 2000, 3000, 4000 and 5000. The restyled 4000 "Force" followed in April 1968 with a new hood and grille and more power, and the 4600 replaced it when the 600 Series came out in December 1975 (Farmers Journal).
Specifications by generation
| 1962–1964 (four-cylinder) | 1965–March 1968 (three-cylinder) | April 1968–1975 (three-cylinder) | |
| Engine | 172 cu in 4-cyl, 3.90 x 3.60 in bore and stroke | Gas and LP: 192 cu in, 4.40 x 4.20 in. Diesel: 201 cu in, 4.40 x 4.40 in | Gas and diesel: 201 cu in, 4.40 x 4.40 in |
| Fuel | Gas, diesel or LP-gas | Gas, diesel or LP-gas | Gas or diesel |
| Transmission | 4-speed, 5-speed, 12-speed over-under, or 10-speed Select-O-Speed | 8-speed dual range or 10-speed Select-O-Speed | 8-speed dual range or 10-speed Select-O-Speed |
| PTO | 540 rpm (540/1000 optional); live with the 5-speed, independent with Select-O-Speed | Transmission or optional independent; 540 and 1000 rpm | Transmission or optional independent; 540 and 1000 rpm |
| Hydraulics | Open center, 5.4 gpm, 2,360 lb lift at the arm ends | Open center, 2,500 psi, 3,200 lb lift, position and draft control | Open center, 2,500 psi, 5.4 gpm, 3,200 lb lift |
| Electrical | Generator; 6-volt (gas), 12-volt (diesel) | Generator, 12-volt, negative ground | Generator, 12-volt, negative ground |
| Weight | 3,162–3,502 lb | 4,885 lb | 4,885 lb |
| Nebraska PTO hp | No test listed by Tractor Data (claimed 43.5 PTO hp) | 46.31 gas 8-speed (test 891); 45.41 gas Select-O-Speed (890); 46.71 diesel 8-speed (893); 45.62 diesel Select-O-Speed (892) | 52.65 diesel 8-speed (test 994); 51.00 diesel Select-O-Speed (995); 50.16 gas Select-O-Speed (999); 52.18 gas 8-speed (1001) |
Sources: Tractor Data for 1962–1964 (engine, transmission), 1965–1968 (engine, tests) and 1968–1975 (engine, tests). PTO figures are at rated engine speed.
Telling the three generations apart
Four-cylinder or three-cylinder. Count the spark plugs or injector lines. Four means a 1962–1964 tractor. The stamping is on the other side, too: the four-cylinder carries its numbers on the left side, on the starter mounting flange (Tractor Data), and the three-cylinder on the right side, behind the starter on the clutch housing (Tractor Data). The four-cylinder 4000 is close kin to the Ford 801, and the N Tractor Club lists CONN-6015J, cast into the lower right side of the block, as the 172 from late 1960 to 1964.
Early or late three-cylinder. Ford changed the sheet metal on the 2000 through 5000 in April 1968 (Farmers Journal):
- Hood sides. Early tractors have vented hood sides. Parts suppliers list the plain side panels as fitting tractors "after 1968, without vents" (Broken Tractor).
- Lower grille. Early tractors use a metal lower grille that wraps around the nose (Broken Tractor, listed for 1965–1968).
- Gas engine. A gas 4000 built before April 1968 has the 192; after, the 201.
- Model code. The first character is the number 4 before April 1968 and the letter D from then on. This is the check that settles it, since hoods and grilles get swapped.
Where the numbers are and how to read them
1962–1964 four-cylinder
The model number sits above the serial on the left-side pad, as on the Hundred and 01 Series. The N Tractor Club decodes the five-digit model number this way:
- First digit: 4 means the 172 engine (2 means the 2000's 134 gas or 144 diesel).
- Second digit: 0 for industrial models built before 1963; 1 for the later industrial and agricultural models. It picks which code list the last digit uses; date the tractor from the serial, not this digit.
- Third and fourth digits: chassis type, such as 10 row crop, 20 utility with adjustable front axle, 31 low center of gravity.
- Last digit: transmission, PTO and hydraulics. With a 1 in second place, 1 is four-speed with PTO, 2 is five-speed with live PTO, 6 is Select-O-Speed with two-speed independent PTO. The full list is in the N Tractor Club guide.
Serial numbers start in 1962 at 1,001, in 1963 at 11,948 (N Tractor Club) or 11,949 (Tractor Data), and in 1964 at 38,931. The same sequence covers the 2000 and the 6000. For the full model-number system, see decoding the Ford Thousand Series.
Worked example (made-up numbers): 41206 over 40512. 4 is the 172 engine, 1 means the later code list, 20 is a utility with an adjustable front axle, and 6 is Select-O-Speed with two-speed independent PTO. The serial is above 38,931, so it's a 1964 4000.
1965–1975 three-cylinder
Three lines are stamped on the right side of the flywheel housing, just behind the starter (Vintage Tractor Engineer):
- Model code. First character: 4 before April 1968, D after. Then two digits for chassis (10 agricultural all-purpose, 20 row crop), one for fuel (1 diesel, 2 gas, 3 LP), one for PTO (for example 2 transmission 540, 4 independent 540), and a letter for transmission (C 8-speed, E Select-O-Speed).
- Date code. Year digit, month letter (A for January through M for December, with no I), day, and shift (A midnight, B day, C afternoon). A Yesterday's Tractors forum thread reads 6F28B the same way: June 28, 1966, day shift.
- Serial number. B for Basildon, England, or C for the US, then the production number.
US serial starts by year from Tractor Data, which My Ford Tractors matches:
| 1965 | C100000 | 1971 | C292100 |
| 1966 | C124200 | 1972 | C327200 |
| 1967 | C161300 | 1973 | C367300 |
| 1968 | C190200 | 1974 | C405200 |
| 1969 | C226000 | 1975 | C450700 |
| 1970 | C257600 |
Worked example (made-up numbers): D1024E / 9C17B / C238410.
- D: a 4000 built April 1968 or later.
- 10: agricultural all-purpose.
- 2: gas, so it should have the 201 gas engine.
- 4: independent 540 PTO.
- E: Select-O-Speed.
- 9C17B: March 17, 1969, day shift.
- C238410: US-built, between C226000 and C257600, so 1969. The serial and date code agree.
Tractor Data lists the same starting numbers for the 2000 and 5000, so the serial dates the tractor but doesn't name the model. A year digit of 5 can mean 1965 or 1975; the serial settles it. Basildon (B) numbers aren't in this table.
Select-O-Speed or manual
The manual three-cylinder 4000 has an 8-speed: a four-speed lever on the left and a high-low lever on the right, stopped to shift. The Select-O-Speed is a 10-forward, 2-reverse full powershift with hydraulic wet clutches that shifts on the move (Tractor Data). Farmers Journal notes the "Jerk-O-Matic" nickname from its delayed, sudden shifts. The 8-speed isn't synchronized, which is why you stop to shift; how a crash-box tractor transmission works explains it. The last letter of the model code (C or E) tells you which one the tractor left the factory with.
What to check before buying
- Match the stamping to the tractor. A manual shifter on a tractor coded E, or a diesel in one coded 2, means major parts were swapped.
- Select-O-Speed under load. Warm it up and pull something in every speed. It should engage promptly without slipping, a long delay or a bang.
- 8-speed. Run through every gear in both ranges and listen for jumping out of gear under load.
- Engine. Check oil pressure warm, look for blue smoke and blow-by, and check the coolant for oil.
- Hydraulics and PTO. A lifted implement shouldn't settle, and an independent PTO should engage smoothly and stop when switched off.
- Electrics on a four-cylinder. A gas 1962–1964 tractor left the factory 6-volt. Check whether it has been converted before buying a battery or charger.
Mistakes to avoid
- Ordering parts by "Ford 4000" alone. Tractor Data calls the three-cylinder entirely different from the 801-based four-cylinder, and a pre-1968 gas engine is a different displacement from a 1968-on one. Give the counter the model code and serial.
- Dating by the hood and grille. Sheet metal gets swapped. The model code's first character is the record.
- Using the US serial table on a B-prefix tractor. Basildon numbers run in their own sequence.
- Buying a slipping Select-O-Speed at a manual-transmission price. Price it as needing a specialist rebuild until it proves otherwise under load.
The smaller sibling, which went through the same changes, has its own page: the Ford 2000.

