Ford 501 Series (1958–1962): Identifying a 541 Offset Workmaster and What to Check
A Ford with its engine shifted off to one side and the seat on the other looks like something homemade until you see a second one. If you've found one with a 501 or Workmaster emblem, it is almost certainly a Ford 541, the offset cultivating tractor in Ford's 1958–1962 01 Series. Sellers often don't know exactly what they have.
This page covers what a 541 is, how to confirm it and tell its versions apart, how to date it from the serial, and what to check before you buy one. It's the written companion to our video on the Ford 541.
What a 541 is
The N Tractor Club's identification guide lists the 501 as the offset member of the 01 Series and decodes a first digit of 5 as a "one row offset tractor" with the 134 cu in gas or LP engine or the 144 cu in diesel (N Tractor Club Quick ID guide). Like the 601 and 701, it was sold as a Workmaster.
Tractor Data lists the 541 as the only model in the 501 Workmaster Series, built 1958 to 1962 at Highland Park, Michigan. It describes the 541 as a cultivating tractor with an offset chassis for a better view of the row, with the engine and driveline offset to the driver's left. That puts the operator on the right, looking straight down at the row being cultivated. Tractor Data names the 2000 Offset (1962–1965) as its successor.
The 501 name is the series, not a model. If someone calls it "a 501," the stamping should still read 541 or 541-4.
The two versions: 541 and 541-4
Tractor Data lists a high-clearance version, the 541-4. The N Tractor Club decodes the -4 suffix as "high clearance with wide front." Tractor Data's dimensions page gives these differences (541 dimensions):
| 541 | 541-4 | |
| Ground clearance | 19.44 in | 25.06 in |
| Standard rear tires | 10-28 | 10-38 |
| Shipping weight | 3,513 lb | 3,664 lb |
The tire size is the quickest field check, because 38-inch rears stand much taller than 28s, but tires get swapped, so confirm with the stamping. Other suffixes can appear too: -L for LP-gas and -D for diesel.
Specifications
| Engine (gas or LP) | Ford 134 cu in 4-cylinder, 3.4375 x 3.60 in bore and stroke, 7.5:1 compression (gas) |
| Engine (diesel) | Ford 144 cu in 4-cylinder, 3.562 x 3.60 in |
| Rated speed | 2,000 rpm gas; 2,200 rpm diesel |
| Power (claimed, not tested) | 35.25 belt hp, 34 PTO hp, 30.7 drawbar hp |
| Transmission | 4 forward, 1 reverse |
| Hydraulics | Open center, Category I three-point hitch |
| Electrical | 6-volt positive ground (gas and LP); 12-volt negative ground (diesel) |
| Wheelbase / length | 89 in / 140.5 in |
| Fuel tank | 11 gal |
| Built | 1958–1962, Highland Park, Michigan |
Figures from Tractor Data's 541, engine and transmission pages. The German Traktorenlexikon also lists 2,000 rpm for the gas engine and four forward gears. The power figures are Ford's claims; the University of Nebraska's 1958–1963 Ford test listings include 601 and 801 tractors but no 541 (1958–1959; 1960–1963).
Telling it from its siblings
From a 701 row-crop (741). Tractor Data classes both as row-crop tractors, and both use the Workmaster engine. The 741's engine sits on the centerline over a narrow or wide front; the 541's sits off to one side. Tractor Data lists an 85.3-inch wheelbase for the 741 against 89 inches for the 541.
From a 601 utility. The 601 is a low, centered four-wheel utility. A 601 can't be mistaken for an offset once you stand in front of it, but a 541 with parts from a 601 can confuse the sheet metal story. Go by the stamping.
From a 2000 Offset (1962–1965). The Thousand Series successor has a five-digit model number. In the N Tractor Club's chart, 11 in the third and fourth positions means offset, and the guide notes the 1962–1964 2000s were painted Ford blue with lighter gray trim, with a restyled grille and no "cyclops" hood emblem.
From a Hundred Series tractor. Ford's 1955–1957 Hundred Series had no offset model, so a 5 as the first digit always means 01 Series.
Reading and dating the serial
The model number and serial are stamped on the left side, behind the starter, on top of the transmission case (Tractor Data). The model is the top line; the serial is below it between two diamond symbols (N Tractor Club).
01 Series serials run across all five families. The N Tractor Club gives 1958: 11,997–58,311; 1959: 58,312–105,942; 1960: 105,943–131,426; 1961: 131,427–155,530; 1962: 155,531 and up. Tractor Data starts 1958 at 11,977 instead of 11,997; the other starting numbers match. My Ford Tractors agrees with the N Tractor Club through 1960. The full chart, including 1957, is in Decoding Ford 01 Series Model Numbers.
Worked example (made-up numbers): 541-4 over ◇109870◇.
- 5: one-row offset.
- 4: four-speed with PTO and three-point lift.
- 1: 01 Series.
- -4: high clearance with wide front.
- 109870 falls between 105,943 and 131,426, so it was built in 1960.
Result: a 1960 Ford 541-4. On the tractor you should see 38-inch rear tires (unless replaced) and noticeably more clearance under the axle housings than on a plain 541.
What to check before you buy one
- The stamping and suffix. Read the full line, including any -4, -L or -D, before you price parts. A diesel changes the engine, the battery and the electrical system.
- The engine casting. The N Tractor Club lists the block part numbers on the lower right side: 310905 for the 1958–1959 134, B9NN-6015C or CONN-6015C for later 134s, and B9NN-6015A for the 144 diesel.
- The front end. Offset tractors were cultivating tractors. Jack the front up and rock each wheel for spindle and axle play, and look for welds where the axle was adjusted or repaired.
- The lift. Raise an implement, shut down, and watch for it settling over a few minutes.
- Oil condition. Look for coolant in the engine oil and water in the transmission and rear end, especially on a tractor that has sat outside.
- The electrical system. Gas and LP models left the factory 6-volt positive ground. Many have been converted, so check before buying a battery; the battery maintainer guide covers 6-volt units.
Mistakes to avoid
- Ordering parts as a 601. The engine is shared with the 601, but the offset chassis, front axle and steering are not. Order by the 541 stamping.
- Buying a 541 for loader work. It was built to cultivate one row with a clear view, not to carry a loader on an offset front end.
- Pricing a 541-4 by its tires. Taller tires can be fitted to a plain 541. Only the stamping confirms a -4.
- Assuming it's Nebraska-tested. The power figures you'll see quoted for the 541 are Ford's claims. Don't compare them directly with tested figures for a 641.
- Dating it with the Hundred Series chart. The 01 Series restarted its serials, so the wrong chart gives the wrong year.